Plumbing 101: Tips for Bathtub Installation
Plumbing 101: Tips for Bathtub Installation
Blog Article
We've noticed this post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the internet and think it made sense to share it with you in this article.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Setting up a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a moderately hard project. If the old bathtub is conveniently easily accessible, the task can move immediately; if you have to open a wall to remove the old tub as well as position the brand-new tub, the task is much harder. In either instance, the task is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub and set in the new one. Ensure you have actually certified on your own for the task as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to think about employing one before you start. Possibilities are you may need a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your restroom if you have currently purchased a new bathtub and do not need to alter the arrangement of your previous water pipes.
Your devices as well as product checklist need to make up the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water system. After doing so, turn on the taps to drain any water remaining in the system. The procedure of eliminating the existing taps can be quite troublesome due to the limited gain access to that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end provides a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in area in between the tap and also the sink. Safeguard the faucet in position with the producer supplied backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former kind must be linked to the tap ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Mounting the Tub
Making use of both wood boards under its feet, place the bathtub in the called for placement. The wooden boards are practical in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four small factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the tub till the level reads degree.
To mount faucets, fit all-time low of the outermost flexible faucet connector to the ideal supply pipe by making a compression join; after that do the same for the other tap.
Turn on the water and examine all joints and also brand-new pipework for leaks and also tighten them if necessary. Fill the bathtub as well as additionally examine the overflow outlet and also the regular electrical outlet for leaks.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been utilized a minimum of once as this will certainly settle it right into its last position.
Preparing for the Installment
First of all, the supporting structure supplied with the bathroom ought to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps device to avoid stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a stiff seal, triggering the water to penetrate the wall between the bathroom and the tiling, leading to complications with moisture and also possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to permit the activity experienced when the bathtub remains in usage. The sealer can split relatively early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very inquisitive about How to Install a Bathtub and I hope you enjoyed the entire page. Kindly take the time to share this page if you appreciated it. Thanks for your time. Don't hesitate to check up our site back soon.
Prices & Booking Report this page